CABLEING

Hi ,
 first we are going to know basics of networking concepts .

what is network ?
a network is a series of points or nodes interconnected by communication paths. Networks can interconnect with other networks and contain subnetworks.
The most common topology or general configurations of networks include the bus, star, token ring, and mesh topologies. Networks can also be characterized in terms of spatial distance as local area networks (LANs), metropolitan area networks (MANs), and wide area networks (WANs).

topologies : 

mesh 

token ring

bus

star

what is networking ?

 communication between the devices or nodes using protocols is called as networking simply by using protocols send/receive data from one node to another node is calles as networking.

Networks may be classified according to a wide variety of characteristics such as the medium used to transport the data, communications protocol used, scale, topology, and organizational scope.
Communications protocols define the rules and data formats for exchanging information in a computer network, and provide the basis for network programming. Well-known communications protocols are Ethernet, a hardware and Link Layer standard that is ubiquitous in local area networks, and the Internet Protocol Suite, which defines a set of protocols for internetworking, i.e. for data communication between multiple networks, as well as host-to-host data transfer, and application-specific data transmission formats.

present we are using 2 types of cables as a media
1.twisted pair cables.
2.unshieled twisted pair.UTP

cross over cable:
for similar devices we are using cross over cable.for example pc-pc,switch-switch etc.

A cross-over cable is a segment of cable that crosses over pins 1&2 and 3&6. This cable is normally used to connect two PCs without the use of a hub, or can be used to cascade two hubs without using an uplink port. Some DSL modems require a crossover calbe to the PC or hub they are connected to. 

 straight through cable :

 For dissimilar  devices straight over cable are using . pc-switch etc

The above tool is called as crimping tool.

UTP :

Cat 5: Out of the three types of cable we’ll be discussing, Category 5 is the most basic. Cat 5 cable is available in two varieties: Unshielded Twisted Pair (UTP), the type widely used in the United States, and Screened Twisted Pair (SCTP), which has shielding to provide a measure of extra protection against interference, but is rarely used outside of Europe. Cables belonging to Category 5 are either solid or stranded: Solid Cat 5 is more rigid, and the better choice if data needs to be transmitted over a long distance, while Stranded Cat 5 is very flexible and most likely to be used as patch cable. Cat 5 cable can support 10, 100, or 1000 Mbit/s Ethernet. The 1000BASE-T standard for Gigabit Ethernet over UTP was designed to work over up to 100 meters of plain old Cat 5.
Cat 5e: Cat 5e (which stands for Category 5, enhanced) cable goes along the same lines as basic Cat 5, except that it fulfills higher standards of data transmission. While Cat 5 is common in existing cabling systems, Category 5e has almost entirely replaced it in new installations. Just like Cat 5, Cat 5e can handle data transfer at 1000 Mbit/s, and is suitable for Gigabit Ethernet. Cat 5e experiences much lower levels of near-end crosstalk (NEXT) than Cat 5.
Cat 6: Of the three cable categories we’re discussing, Category 6 is the most advanced and provides the best performance. Just like Cat 5 and Cat 5e, Category 6 cable is typically made up of four twisted pairs of copper wire, but its capabilities far exceed those of other cable types because of one particular structural difference: a longitudinal separator. This separator isolates each of the four pairs of twisted wire from the others, which reduces crosstalk, allows for faster data transfer, and gives Category 6 cable twice the bandwidth of Cat 5! Cat 6 cable is ideal for supporting 10 Gigabit Ethernet. Since technology and standards are constantly evolving, Cat 6 is the wisest choice of cable when taking any possible future updates to your network into consideration. Not only is Category 6 cable future-safe, it is also backward-compatible with any previously-existing Cat 5 and Cat 5e cabling found in older installations.

What are the maximum lengths for cables?

For Solid UTP:
Fast Ethernet 100baseT 100 Meters (328 feet)
Twisted Pair Ethernet 10baseT 100 Meters (328 feet)

Recommended maximum lengths for Patch Cables made from stranded cable:
Fast Ethernet 100baseT 10 Meters (33 feet)
Twisted Pair Ethernet 10baseT 10 Meters (33 feet)

                                                     Thanks for reading